T-Shirt Forums banner

1 - 15 of 15 Posts

·
Registered
Joined
·
34 Posts
Discussion Starter · #1 ·
Hi all,
Having gone through the nightmares of all the error codes on my blazer pro and changing every part possible i thought these small explanations might help others
Error Codes (Maintenance)
0002 Carriage Motor / Ink Tube end of life (Clear Carriage Motor Counter)
0004 Nozzle check error
0008 RTC error (Real Time Clock) (Check the Battery and reset the Date and Time)
0010 Multi Sensor Error
0020 Print Head life counter (Reset the Head counter)
0040 Cleaner Unit end of life (Clear the Cleaner counter)
0080 Date is not set (Set the date and time (RTC))
0100 RTC Battery low (Replace the battery, and reset the RTC)
0200 Paper feed roller life (over 75,000 sheets) (Reset the ASF counter)

Error Codes (Service)
00000088 RTC (Real Time Clock) data is corrupted
00000101 Carriage Motor life (Reset Carriage Motor Counter, check for leaky ink tubes)
00000103 RTC (Real Time Clock) battery is defective
00000105 Print Head end of life (Inspect print head and reset head counter)
00010000 Paper Feed Motor encoder check error (Check Sensor and Timing Disk)
00010001 Paper Feed Motor out of step
00010002 Paper Feed Motor overcurrent (Check for mechanical binding of the feed rollers / motor)
00010003 Paper Feed Motor in-position time-out
00010004 Carriage Motor encoder check error (Check sensor and Timing Disk)
00010005 Carriage Motor out of step
00010006 Carriage Motor overcurrent (Check for mechanical binding, If not replace motor)
00010007 Carriage Motor in-position time-out
00010008 Servo interrupt watchdog time-out
00010009 System interrupt watchdog time-out
0001000A Carriage home position error (Check Sensor and mechanical components)
0001000C Platen Gap home position error (Check Sensor and mechanical components)
0001000F Carriage Motor PWM output faulty
00010010 Paper Feed Motor PWM output faulty
0001001B Head driver (TG) temperature error
0001001D Carriage servo parameter error

0001001E Paper feed servo parameter error
00010020 CSIC read / write error
00010022 Ink type error
00010023 RTC (Real Time Clock) (Reset RTC)
00010025 CSIC ROM communication error
00010026 RTC (Real Time Clock) communication error
00010028 Head error
00010029 Unidentified NMI
0001002A Carriage ASIC ECU error
0001002B Paper feed ASIC ECU error
0001002D Cleaning Unit end of life
0001002F 360 DPI writing time out error
00010030 Multi Sensor failure (1. Check sensor, 2. calibrate sensor, 3. replace sensor)
00010031 ASF (Auto Sheet Feeder) home position error (Check Sensor and mechanical components)
00010032 ASF (Auto Sheet Feeder) Drive Switch error (Check Sensor and mechanical components)
00010033 Exit Roller home position error (Check Sensor and mechanical components)
00010034 Eject Roller lifted (Customer Safety Sensor on the eject roller)
00010035 Pump Home Position Error (Check Sensor and mechanical components)
00010036 Type B 1394 (Firewire) board installation (Remove Firewire Card / not allowed)
00010037 Print Head thermistor error
00010038 Head Driver thermistor error
00010039 PG adjustment value NVRAM error
0001003A PG adjustment value NVRAM error
0001003B Carriage Lock / Cutter Error
0001003C Carriage Lock / Cutter Error
0001003D Carriage Lock / Cutter Error
00020000 NVRAM error
00020002 SDRAM error
00020003 BOOT program SUM error
00020009 Flash memory SUM error
0002000A Program load error
0002000B Internal memory shortage error
0002000C Review error
100000E0 CPU address error (load misalignment)
10000100 CPU address error (storage misalignment)
10000180 CPU reserve command code exception error
100001A0 CPU slot illegal command exception error
100001C0 AC disruption (AC Power) (Unplug and wait 30 sec., then plug back in)
100005C0 CPU DMA address error
0003xxxxx –
0Dxxxxxxx CPU error
 

·
Registered
Joined
·
2 Posts
I keep getting error code 0001001D. The printhead/carriage is too low. The 2 bars that hole the carriage keep lowering it so low it hits the capping station. Even if I manually move the gears to raise it. It will print fine once or twice but eventually will lower back down to hit the station . Any help ?
 

·
Registered
Joined
·
2 Posts
00010028 Head error. I have been searching for days and still have found nothing more descriptive that simply Head error. If Someone could tell me a little more about how to fix this or at least what is wrong with the head, it would be greatly appreciated.
 

·
Registered
Joined
·
5,720 Posts
00010028 Head error. I have been searching for days and still have found nothing more descriptive that simply Head error. If Someone could tell me a little more about how to fix this or at least what is wrong with the head, it would be greatly appreciated.

From Michael in our Support Department:

This error is not very common. All you can do is check all the ribbon cables from the printhead to the front board (you can see that when you open the cover) and through to the main board. Replace the printhead. If the error persists, you will need to replace the front board and/or the main board.

There is no way to "fix" a printhead that is behaving like this.



Harry
Equipment Zone
 

·
Registered
Joined
·
27 Posts
Hello,
I'm stuck with the 1000A error carriage home position error. I'm not sure as exactly which sensor I should check...
 

·
Registered
Joined
·
4 Posts
Does anybody know how to fix this error code?I'm thinking it means I need a new motherboard? 100000E0 - CPU address error (load misalignment)

Cheers
 

·
Registered
Joined
·
3 Posts
Hello everyone, I have a DTG printer and require some help on a problem I encountered. My printer it's a fast tjet blazer express with a brand new head, brand new lines, and a brand new capping station. The issue is that whenever I try to print something, the only color that actually prints is yellow no matter what kind of colors are on the image. I don't know how to get the other colors to print, I don't know if it's the mother board, the ribbons, the encoder strip, or just a configuration error, please help. Any advice would be helpful, thanks.
 

·
Registered
Joined
·
5,720 Posts
Hello everyone, I have a DTG printer and require some help on a problem I encountered. My printer it's a fast tjet blazer express with a brand new head, brand new lines, and a brand new capping station. The issue is that whenever I try to print something, the only color that actually prints is yellow no matter what kind of colors are on the image. I don't know how to get the other colors to print, I don't know if it's the mother board, the ribbons, the encoder strip, or just a configuration error, please help. Any advice would be helpful, thanks.

What does your nozzle check show?

_
 
1 - 15 of 15 Posts
Top