T-Shirt Forums banner

1 - 10 of 10 Posts

·
Registered
Joined
·
7 Posts
Discussion Starter #1
こんにちは。

私は永遠のレーザーダーク(低温)を使用しています。

接着を行うと、ドットが発生することはほとんどありません。

印刷段階では発生しないため、接着工程または接着自体が原因と考えられます。

誰かが同じような現象を起こしましたか?

解決策ができてください。

PXL_20210207_061845422.jpg

272339


272340



272341
 

·
Administrator
Joined
·
14,492 Posts
Japanese Google translate:

Hello. I use eternal laser dark (low temperature). When glued, dots are rarely generated. Since it does not occur at the printing stage, it may be due to the bonding process or the bonding itself. Has anyone had a similar phenomenon? Please have a solution.
 

·
Registered
Joined
·
2,584 Posts
Improved translation:
Hello. I'm using the FOREVER laser dark (low temperature) paper.
When the sheets are glued together, dark spots are some times generated.
As this is not happening at the printing stage, it is most likely caused by the bonding process or the adhesive itself.
Has anyone had a similar problems? Do you have a solution please?
Most likely defective batch of paper.
Maybe the adhesive layer has dimples.

And my attempt in Japanese.
おそらく欠陥のある用紙のバッチ。
たぶん接着剤層にくぼみがあります。
 

·
Registered
Joined
·
7 Posts
Discussion Starter #4
Most likely defective batch of paper.
Maybe the adhesive layer has dimples.

And my attempt in Japanese.
おそらく欠陥のある用紙のバッチ。
たぶん接着剤層にくぼみがあります。
Thank you.
I always check for dents before gluing.
 

·
Registered
Joined
·
7 Posts
Discussion Starter #6
[QUOTE = "TABOB、投稿:4488913、メンバー:866018"]
不良紙のくぼみが見えない場合があります。
それは接着剤の表面の下に隠された泡のようなものです。
View attachment 272399
[/見積もり]
情報ありがとうございました。

次に、ドットが表示された場合は、運が悪かったと考える必要があります。

またはあなたは何をすべきか知っていますか?
 

·
Registered
Joined
·
2,584 Posts
次に、ドットが表示された場合は、運が悪かったと考える必要があります。
またはあなたは何をすべきか知っていますか?
Hmmm... I have an idea.

You could patch the black spots using a small piece or coating from the B sheet of the transfer paper.
Just place it over the black spot and use a heat gun to melt it.

Alternatively, you could make a paste using the the coating from a B sheet and distilled water. Then you can apply the paste with a small brush.
 

·
Registered
Joined
·
7 Posts
Discussion Starter #8
Hmmm... I have an idea.

You could patch the black spots using a small piece or coating from the B sheet of the transfer paper.
Just place it over the black spot and use a heat gun to melt it.

Alternatively, you could make a paste using the the coating from a B sheet and distilled water. Then you can apply the paste with a small brush.
Thank you very much.
I will try it the next time a dot appears
 

·
Registered
Joined
·
7 Posts
Discussion Starter #9
Thanks to everyone who gave me advice.

As you pointed out, it was caused by the air in the B paper.

This time, most of the 500 sheets of B paper I ordered contained air.

Is this a common thing?
Or is it a defective product?
 

Attachments

1 - 10 of 10 Posts
Top