T-Shirt Forums banner

Blowouts and Emulsion Pealing

3K views 15 replies 9 participants last post by  FantasTico 
#1 · (Edited)
Hello guys,

I had a major issue this morning. Bear in mind I'm pretty new to doing this on my own.

I'm using Image Mate PC701 fast exposing emulsion and a 230 mesh screen. I use a light table that I removed the plexiglass film and fitted with 3 black light tubes. I successfully burned one design a few nights ago (cooked for about 2 minutes) and it washed out fine.

I don't have a "dark room" yet, so what I do is coat my screen(s) in my garage under a bug light at night. I then let them dry in complete dark and come back later the same night and burn it. Two nights ago I started coating pretty late and was getting tired. Instead of staying up to burn the screen after it dried, I put the screen on some blocks, print side down, inside of a cardboard box and taped it closed.

This morning I pulled the screen out of the box and set it to burn the stencil, using the previously established 2 minutes. I was burning some highly detailed (small print) neck tags with a 230 mesh screen.

When I went to lift the screen off the light table, I noticed the stencil film was stuck to the screen. I had large areas of the text and design wash out. In addition, the screen felt tacky and I was literally able to peal the emulsion away like skin after a sun burn.

What do you think my issue was? Is it possible the emulsion hadn't tried over a 24+ hour period because it was insulated in the box? Or maybe the stencil hadn't dried yet? I doubt burning longer would have helped as that would have just made me rinse longer and cause more blowouts. Any clue?

Thanks!
Kevin
 
See less See more
#4 ·
I'm sure it was humid. I'm in Oklahoma and it gets very humid here this time of year. I'm sure being wet and insulated inside of a hot box didn't help either.

Would a fan help with the drying in lieu of me buying a dehumidifier? I've already spent a couple thousand dollars on my setup and have yet to see a dime back. I do plan on buying one, just not right this moment.
 
#3 ·
Definitely a humidity issue. Screens should be at 40% or lower Humidity during drying, storage and exposure. If you store in a non controlled humidity environment you need to lower humidity at least 2-4 hrs before exposure. Also I recommend a few more bulbs to your exposure unit. As you start to do more detail you will suffer undercutting before proper exposure.
 
  • Like
Reactions: lazerstruck
#5 ·
You can try but not having your screens at a set humidity level will change your exposure times. You definitely need air flow even with a dehumidifier.
 
  • Like
Reactions: lazerstruck
#8 ·
We had some storms blow by tonight. That pushed out the humidity and brought in dry, cold air. I coated a new screen and this time set up a regular box fan a few feet away from the drying rack. Dried solid in about 3 hours. Burned it and the text/artwork came out beautifully.

Thanks a TON guys - Awesome advice.
 
#10 ·
Looks to me like you didn't get the screens dry and/or have a very bad humidity problem. Not only does damp emulsion not stick to the fabric but it also increases the the exposure time dramatically. I built a dryer cabinet out of plywood. Yeh I know plywood burns. it was set up for the screens to lay horizontal with only the edges of the screens touching the rack. I then put a hole in the side large enough for a small portable heater to blow air in. Heater has a built in thermostat so it doesn't get to hot. The box is light tight so I can also store my screens in it. the gentle air movement with a little heat dry the screens fairly quickly. The box holds 12 screens. I have used it for about 15 years with no problems. I never leave it on unless I'm close by. I have considered making one out of metal but haven't got to it.
 
#11 ·
I've since built a dark/drying box myself. I basically did the same thing you did with my dry box. Built it out of 2x4's, 1x2's, and plywood. Put in a screened opening near the bottom with a fan on the inside to pull in air, and a light-proof opening near the upper-rear to push air out. Sealed all the edges with caulk. Finished the door off with a foam border to ensure the light stays out. Works really well.

I've burned several screens successfully now. Just did a 200 shirt run with a 3-color design and didn't have a single problem until I went to clean up the screen for archiving. My screen wash basically smeared the left over ink (after carding) to the emulsion, then started loosening up areas of the stencil. Ended up reclaiming the screens.

I'm wondering if my issue is that I diluted my screen wash 50/50 with water. No clue... I'm planning on just archiving my screens in trash bags until I get my shipment of Citra Paste. I'll give that a try - says it specifically won't mess with emulsion.
 
#12 ·
Screen wash/ press wash typically is applied with no water. Citra paste on the other hand is used with water.

If you tried to used water with screen wash 147 it would just smear. If your going to try and catalog screens you need to post expose( just put out in sun ). But also work fast as water is a enemy of emulsion.
 
  • Like
Reactions: lazerstruck
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top