[DTG Brand] Problem with M2 no display - T-Shirt Forums
 

Hi, Unregistered. | Today's Posts

T-Shirt Forums
User Name
Password

Register Today For Free!

Forgot Your Password?





Site Navigation








+   T-Shirt Forums > T-Shirt Industry Information > Direct to Garment (DTG) Inkjet Printing > DTG Brand
Discussion, tips, pictures, reviews and peer to peer support for current and future DTG Brand garment printer owners.



[DTG Brand] Problem with M2 no display

 
Share This Thread Thread Tools
Old April 14th, 2018 Apr 14, 2018 10:10:55 AM -   #1 (permalink)
Forum Member
T-Shirt Apprentice

Savage Edge's Avatar
 
Member Since: Mar 2018
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Problem with M2 no display

I recently purchased a used DTG M2 printer. I am having a couple problems getting it setup. The first problem is when I push the load button the printer shakes and has a hard time loading the bed. It keeps popping the E 065 error x motor error. After resetting it and trying multiple times now the display doesn't show anything. The roll light is off and the power light is a faint green not blue but the data light is on. Anyone have any ideas??
 
Sponsored Links
Advertisement
 
Old April 15th, 2018 Apr 15, 2018 2:56:58 PM -   #2 (permalink)
T-Shirt Lover
T-Shirt Fan

Screen168's Avatar
 
You can call me: Screen168
Member Since: Feb 2016
Posts: 36
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Re: Problem with M2 no display

also i same problem
 
Old April 15th, 2018 Apr 15, 2018 2:57:33 PM -   #3 (permalink)
T-Shirt Lover
T-Shirt Fan

Screen168's Avatar
 
You can call me: Screen168
Member Since: Feb 2016
Posts: 36
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Re: Problem with M2 no display

check ram again
 
 
Old April 15th, 2018 Apr 15, 2018 4:31:09 PM -   #4 (permalink)
Forum Member
T-Shirt Apprentice
Thread Starter

Savage Edge's Avatar
 
Member Since: Mar 2018
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Re: Problem with M2 no display

Quote:
Originally Posted by Screen168
check ram again
Where is the ram located on the printer?
 
Old April 20th, 2018 Apr 20, 2018 1:25:31 AM -   #5 (permalink)
T-Shirt Lover
T-Shirt Aficionado

uktech's Avatar
 
Member Since: Jun 2009
Location: UK
Posts: 260
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 4
Thanked 39 Times in 37 Posts


Default Re: Problem with M2 no display

The error 065 usually means there is no power from the main board to the PF motor, this could be a motor fault or the IC (chip) that drives the motor on the mainboard has blown. No display is either a fault on the ribbon cable from the display to the mainboard, or the RED circular fuse FH8 has blown on the mainboard.
__________________
Engineers build things, technicians swap things out
 
Old April 25th, 2018 Apr 25, 2018 1:15:08 PM -   #6 (permalink)
T-Shirt Lover
T-Shirt Fan

Screen168's Avatar
 
You can call me: Screen168
Member Since: Feb 2016
Posts: 36
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Re: Problem with M2 no display

Quote:
Originally Posted by Savage Edge
Where is the ram located on the printer?
backside machine on mainbord mutoh
 
Old April 30th, 2018 Apr 30, 2018 10:19:07 AM -   #7 (permalink)
Forum Member
T-Shirt Apprentice
Thread Starter

Savage Edge's Avatar
 
Member Since: Mar 2018
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 0
Thanked 0 Times in 0 Posts


Default Re: Problem with M2 no display

Quote:
Originally Posted by uktech
The error 065 usually means there is no power from the main board to the PF motor, this could be a motor fault or the IC (chip) that drives the motor on the mainboard has blown. No display is either a fault on the ribbon cable from the display to the mainboard, or the RED circular fuse FH8 has blown on the mainboard.

I replaced the ribbon cable from main board to control board and no change. I also noticed the fans hooked to the main board are not working either. I assume the main board is shot and and needs to be replaced. Does this sound about right?
 
Old May 11th, 2018 May 11, 2018 6:05:14 AM -   #8 (permalink)
T-Shirt Lover
T-Shirt Aficionado

uktech's Avatar
 
Member Since: Jun 2009
Location: UK
Posts: 260
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Thanks: 4
Thanked 39 Times in 37 Posts


Default Re: Problem with M2 no display

Not 100% that the mainboard is dead, the fuse that is related to that on the mainboard is repairable. Its the round red fuse (FH8) near the ribbon cables. Check to see if it has blown, replace and test the printer before throwing out a good mainboard.
__________________
Engineers build things, technicians swap things out
 






This is a discussion about Problem with M2 no display that was posted in the DTG Brand section of the forums.

Quick Reply
Type Your Message Below:
Do NOT Post Self Promotional URLs, Advertisements, Sales Offers or Requests. It is against our Forum Guidelines.
Options

Register Now

In order to be able to post messages on the T-Shirt Forums, you must first register.


Please enter your desired user name, your email address and other required details in the form below.

Your username must be between 2 and 16 characters and contain only letters and numbers (no special characters like hyphens, *, ', ~, etc)
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

A confirmation email will be sent to this address, so please make sure it is accurate and that your email software is set to allow emails from our domain: t-shirtforums.com (sometimes the confirmation email gets accidently filtered into Yahoo/AOL/Hotmail/Gmail spam folders)
.

You won't be able to post until your email address has been confirmed. We take your privacy very seriously. Feel free to review our Privacy Policy in a new window.
Email Address:
First Name
It's nice to be able to be on a "first name" basis with the people you talk to in a forum. This is a totally optional field; if you like being on a first name basis, please enter your first name below :)

Log-in


Thread Tools

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off
Trackbacks are On
Pingbacks are On
Refbacks are Off
Trackbacks are On
Pingbacks are On
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Nozzle pressure problem Kuchciak Resolute DTG 5 March 3rd, 2016 06:21 AM
panther / jaguar II weird problem! help! jlugo98 GCC Brand Vinyl Cutters 6 April 27th, 2015 10:02 PM
[Anajet] Problem With Anajet Fp-125 LCD display and printing somegadollar Anajet 17 April 3rd, 2015 08:08 PM


All times are GMT -8. The time now is 12:20 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2004-2014 T-ShirtForums.com. All rights reserved.