102557

Quote: Originally Posted by tieutusamac This is a Epson 1400 Printer had converted to DTG By me. Please check it out and tell me what do you think about it? Here is a link: Thank you for looking, Tieutusamac

Very cool...

can you start the 1400 with no platen in place without error? can you print a second shirt in succession without powering off? we used to do as your video shows with the work force 1100 (start it with platen in place) what the 1100 did was pull the platen in when it runs its start up sequence "trip the pe" then you could print... but without the platen in place it would error... and when we tried printing in succession the timing was off!! we could get it to work maybe one out of eight times..

are you having better luck with the 1400 in that respect?

also do use white ink in it yet? im interested if it will lay down enough with the two channels!

 

Reply With Quote Quick reply to this message

tieutusamac

For Mr. German13

At first, No, this printer cannot start without platen on it. However, it can print a second shirt or more without power off, just pull the platen back enough to pass the paper sensor and it ready to print the next one.

No, I have not used the white ink yet!

Thanks
Tieutusamac

 

Reply With Quote Quick reply to this message

sonoduce

Hello, I have a serious problem with ink or drying after washed first clears 50% from what I can not selling this product
I am using ink dtgink and while employment is 170 ° (350) for 60 seconds
I understand that any locking is needed for white t-shirts
Thank you

 

Reply With Quote Quick reply to this message

cmos

At first, is the shirt 100% cotton?
You must hover the heatpress above the shirt for 10 seconds, then lay a sheet of parchment paper above the shirt and then you need to press for 2 minutes with light pressure
Try also to lift the press at the 1st minute for 10 sec and the press for another minute

 

Reply With Quote Quick reply to this message

sonoduce

Thank you for answer, I imagine that the other wonders, proves with 170 ° (350) for 120 seconds to see if not cleared
Thank you

 

Reply With Quote Quick reply to this message

antonis

thanks a lot German 13...i'm trying to find the service manual for 1100 or 1900...any idea?

 

Reply With Quote Quick reply to this message

tieutusamac

Here is my printer can print on the Ceramic tile.

Thank 4 watched
TTSM

 

Reply With Quote Quick reply to this message

spiderx1

What ink are u using for tile. Using a non textile pretreat??

__________________
All American Atlanta Branch,Epson F2000, NeoFlex DTG, Sales Demo and Training in Atlanta Ga. Dupont Inks, Image Armor PT sales.

 

Reply With Quote Quick reply to this message

antonis

very intersting! what about the inks?

 

Reply With Quote Quick reply to this message

tieutusamac

I used normal Epson ink. The inks are not biggest things. The problem is the coat for the tile only!
Thanks for asking

 

Reply With Quote Quick reply to this message

antonis

thanks for the reply

__________________
respect the old, create the new!

 

Reply With Quote Quick reply to this message

warco

This thread is a bit old but thought this would be helpful to some.
I thought I could make a go of a WF30 (work force 30) thinking since it was a current offering, they would be available into the future.
Result - is it way to hard to get the sensors to work properly. Do not waste your time. Plus the housing and frame are almost entirely plastic so there was a lot of "fab" work to make a support for the printer head assembly. I wish I would have found this info before I tried. Onto a 1900 or 2200 now.

 

Reply With Quote Quick reply to this message

kandim10

Quote: Originally Posted by colorfinger The PE sensor or paper sensor. It is a trigger type sensor that is tripped when paper pushes it. I have concluded that the problem is with the timing of this sensor. It is tripped twice... Once to verify paper and secondly when printing commences. If the timing is off you will get a paper feed error. You can remedy paper feed errors created by the PW sensor by turning edge to edge printing off... Bob ?;O)

hai guys ,,can you tell me how to setup paper sensor on DTG T1100,,becouse mine always error/paper jam,,will be good if you have picture of it,,thanks

 

Reply With Quote Quick reply to this message

edward1210

Quote: Originally Posted by kandim10 hai guys ,,can you tell me how to setup paper sensor on DTG T1100,,becouse mine always error/paper jam,,will be good if you have picture of it,,thanks

I'm giving up in my dream to build my own dgt with epson 1400
I sent to print, pc communitcate with the printer, the head move to the other side, than paper and ink light error on.
I gave up

__________________
[email protected]
http://www.amvisionprint.net

 

Reply With Quote Quick reply to this message

dragonknight

Quote: Originally Posted by edward1210 I'm giving up in my dream to build my own dgt with epson 1400 I sent to print, pc communitcate with the printer, the head move to the other side, than paper and ink light error on. I gave up

Never give up, I have been through a lot of problem also before and right now I am in the middle of modifying Epson Pro 3800, see here https://www.t-shirtforums.com/diy-dtg/t170993.html. Ask some help to the forum and post some videos of your printer error if necessary, I guess there are a lot of people here willing to help you to finish your DIY DTG Printer

__________________
DTGPrinters DTG, Embroidery, Screen Print, Vinyl, Blank T-Shirts Services from Indonesia; Discovery-Jet / Purikura Digital Printing

 

Reply With Quote Quick reply to this message